You are here: Home > Drivers > Firmware > Others > Pentax EI-200 Firmware 1.11

Pentax EI-200 Firmware 1.11

Pentax EI-200 Firmware 1.11 is an essential driver for Firmware, by Others. Before installing the new EI-200 Firmware (version 1.11), please carefully read through all the information contained below.

Publisher:
Others
Language:
Version:
See above
Run on OS:
Windows All
License:
Free
Price:
Free
File type:
.zip
File size:
3.1 MB
Updated on:
May 22, 2013
Reviews:
Check Reviews
Rating:
Softmenu rating: 6/10

Pentax EI-200 Firmware 1.11 Reviews - by Softmenu Drivers Editor

Pentax EI-200 Firmware 1.11 is a driver for computer's Firmware. With the latest version of Pentax EI-200 Firmware 1.11, you can have your PC worked correctly or better.

Driver Description - by Publisher

Drivers Description, released by Others. please read it carefully before you download.

Full Drivers Description see below:

Before installing the new EI-200 Firmware (version 1.11), please carefully read through all the information contained below.



This document contains step-by-step instructions on how to upgrade the firmware on your PENTAX EI-200 Digital Camera. This version of the firmware will improve picture quality by increasing the accuracy of color reproduction and reducing image noise. Before updating your firmware, we recommend printing this document to use as a reference.



You may update the firmware on your EI-200 by downloading the updater file via the web, and following the instructions on this page. You can also send your camera to PENTAX CORPORATION to have your firmware updated. We will perform the update for free, but you will be responsible for any shipping costs to get your camera to us.



Cameras compatible with this update:

This software will update EI-200 cameras that have firmware versions 1.0 or 1.02 to version 1.11. To check your current firmware version, begin by turning the camera on in picture capture mode. Press the DISPLAY button to activate your LCD display. Next, press your right soft key (labeled STATUS) for current camera settings including firmware version.



Note:

We strongly recommend the use of the EI-200 A/C adapter when performing this update. Any power interruption during this procedure (approximately 4 minutes), such as battery depletion, may result in potential harm to your camera's logic board, requiring service to your camera. This service will NOT be covered under the terms of your PENTAX product warranty. Please contact Customer Service at 800-877-0155 for information on ordering an A/C adapter, or if you are unclear about any information contained in this document.


Instructions:

Download (and decompress) the firmware update file fwdc001t.fwi to your computer's hard drive.

1. Reformat your EI-200's CompactFlash card (the Reformat command is found in the General Preferences menu when the camera is in picture capture mode), then connect the camera to the computer via the USB cable as per the instructions in your camera's manual.
2. Transfer the update file, fwdc001t.fwi , to the root directory of your camera's CompactFlash card. The camera's CompactFlash card is represented by the "Removable Disk" icon that appears when you connect the camera to the computer.
3. When the camera's orange disk access light stops blinking, the file has been fully copied to the CompactFlash card.
4. Turn your camera off and detach it from your computer.
5. With the A/C adapter powering the camera, open the CompactFlash slot door on your camera and turn your camera on. (The CompactFlash slot door on your camera must remain open during the installation of the firmware.)
6. Instead of powering on normally, your orange disk access light will blink for a minute while the camera is preparing the update. When the camera is finished preparing the update, your LCD display will show a progress bar as the update runs to completion.
7. Once the update is complete, the progress bar will disappear (i.e. the LCD screen will go blank) and the camera will restart normally.
8. When you are done with the firmware update, reformat the CompactFlash card in the camera (the Reformat command is found in the General Preferences menu when the camera is in picture capture mode) prior to using the camera.
9. To confirm the new version of the EI-200 firmware, turn the camera on in picture capture mode. Press the DISPLAY button to activate your LCD display. Next, press your right soft key (labeled STATUS) for current camera settings including firmware version. The new version should read "1.11" at the bottom of the display.


It is highly recommended to always use the most recent driver version available.
Do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games.

Try to set a system restore point before installing a device driver. This will help if you installed a wrong driver. Problems can arise when your hardware device is too old or not supported any longer.

Supported Operating System:

Windows All

Running requirements

Need not extra requirement except the OS environments mentioned above.

Limitations

Please check the license above, if this is a freeware, it will be no limitation, else it may have the days or times limitation, please read the specifications attached with the download file carefully.

Tested virus free - Pentax EI-200 Firmware 1.11 has been tested to be a safe driver on May 22, 2013.

Drivers Searches Related to Pentax EI-200 Firmware 1.11

Bookmark or share this page to your friends

copy softmenu.org bookmark
copy softmenu.org bookmark
copy softmenu.org bookmark

Pentax EI-200 Firmware 1.11 Related Drivers

Creative Nomad MuVo Micro N200 firwmare 1.11.01

N200 is a ultra-light, high-performance Digital Audio Player with super fast USB 2.0 that lets you enjoy hours of WMA or MP3 digital music anywhere. Offered with 128MB, 256MB or 512MB ...

Dell PowerEdge 1650 TEAC DV-28EC Firmware 16.11.20

System Features:CD/DVD: Teac CD-224ECPU: Intel Pentium III 1.26GHzHard Disk Drive: 2 Seagate ST318305LC , SCSI-2Hitachi DK32DJ-18MC , SCSI-2Host Bus Adapter: Dell PERC 3/Di , SCSI-2Video ...

Dell Dimension 1100 TSST TS-H192C Firmware 14.11.2

Key FeaturesForm Factor Micro Tower Processor Intel Pentium 4 2.8 GHz Installed Memory 256 MB (DDR SDRAM) Operating System Microsoft Windows XP Home EditionProcessorProcessor Type Intel ...

Dell XPS 420 Media Card Reader with Integrated Bluetooth Module C

Dell XPS 420 Media Card Reader with Integrated Bluetooth Module CAB-200 Firmware A01 New Fixes:1. Support HC MMC Plus (4GB on) media2. Supports SD card spec-out-of SD 2.03. Fix boot / resume issues.

Dell Dimension 2400 TSST TS-H192C Firmware 14.11.2

Processor * Type * Intel Pentium 4 2.66 GHz * Installed Qty * 1 * Max processors supported * 1Cache Memory * Type * L2 cache * Installed Size * 512 KB * Cache Per Processor * 512 KBMainboard ...

NDC NWH9210/NWH9200 Firmware 1.15-2003

National Datacomm Corporation (NDC) was founded in 1990 in the Hsin-Chu Science Park, Hsin-Chu, Taiwan. NDC's key founders have extensive technical and management experience in the ...

Latest Download Topic